Technical information: helmet cleaning and disinfection machines

On this page you will find detailed technical information about CENTRUMO helmet cleaning and disinfection machines, their functions, possibilities of use, operational requirements and available configurations.

Our machines provide a self-service solution for hygienic helmet treatment, freshening and care. They are suitable for businesses where helmets are regularly used, hired out or shared, and can also offer customers an additional paid service.

The machines combine spraying a compatible disinfectant, UV treatment, airflow, removal of loose dust particles and fragrance application. The process runs automatically without an operator being present throughout.

The main advantages include:

Self-service operation without the need for permanent staff presence.
Short cleaning programmes with different treatment times and intensities.
Possibility of cashless payments through an optional payment terminal.
Online monitoring and remote management of operation.
Installation without water and sewage connection.
One-chamber and two-chamber design according to the needs of the operation.
Possibility of branding and individual modifications of the device.

Technical parameters, availability of functions and setting options may vary according to the specific model and ordered configuration. We continuously refine the data according to available information from the manufacturer. A binding specification is always part of a specific offer.

1. Available models: SINGLE and DUO

Our CENTRUMO machines come in two main versions, differing primarily in the number of chambers and intended use.

SINGLE – machine with one chamber

Model SINGLE (EKH01) represents a compact self-service device for treating one helmet at a time.

It is especially suitable for:

Businesses with low to moderate customer traffic.
Motorcycle stores and specialized stores.
Sports equipment rentals.
Smaller sports and leisure centers.
Operators who want to offer an additional service to customers.

DUO – machine with two independent chambers

The DUO model (EKH01DUO) is equipped with two separately controllable chambers.

Each chamber can be triggered independently of the other, so it is possible to use only one chamber or both at the same time.

This variant is especially suitable for:

Businesses with higher customer traffic.
Karting tracks and motorsport centers.
Bike parks and sports rentals.
Ski resorts.
Operators with a larger number of shared helmets.

DUO can treat equipment in two chambers at the same time, helping increase throughput during busy periods.

Individual and custom design

Following a technical assessment, selected machines can be adapted with custom graphics, language versions, payment configurations, modified programmes or adjustments for specific equipment.

Custom modifications are not an automatic part of the standard design and their availability is assessed individually.

2. How is the helmet cleaned and disinfected?

The process is designed as a simple self-service operation controlled by the customer through the touchscreen.

1. Inserting a helmet

The customer places the compatible helmet into the chamber following the instructions on the display. Gloves can also be treated together in one cycle if they are sized and positioned correctly.

2. Program selection and possible payment

The customer selects an available programme on the display. If the machine provides a paid service, the customer pays using a supported payment method.

3. Automatic treatment of equipment

The device starts the selected cycle, which, depending on the model and settings, uses a combination of fine spraying of the product, UV treatment, air flow, negative pressure and fragrance refreshment.

The exact sequence and duration of each stage depend on the specific machine configuration.

4. Cycle completion and pickup

Once the programme ends, the customer removes the helmet. The machine is primarily intended for hygienic treatment and freshening, rather than mechanical removal of heavy dirt.

3. Available cleaning programs and length of cycles

Machines can offer several programs with different treatment lengths.

Program	Approximate length
Quick	Approximately 3 minutes
Medium	Approximately 5-7 minutes
Deep	Approximately 10 minutes

Quick is the shortest available programme, while Deep provides a longer treatment cycle.

For individually set combinations, the Medium program can be configured for approximately 5 minutes.

The given times are indicative. The specific availability of programs, their length, intensity and sequence of individual phases depends on the delivered version of the machine. The exact setting is confirmed when ordering.

4. What technologies does the machine use?

The devices combine several technologies designed for hygienic treatment, removal of loose dirt and refreshment of equipment.

Disinfectant spraying

The machine applies a suitable compatible disinfectant or cleaning agent in the form of a fine mist, also referred to as atomization.

The chemical composition of the preparation must correspond to the requirements of the equipment and the treated materials.

UV technology

The process includes UV treatment, complementing the other stages of hygienic care.

The effectiveness of UV technology depends on the design of the device, the duration of exposure and the specific conditions of use.

Exact UV dose and microbiological effectiveness are not documented in the available documents. Specific claims about disinfection effectiveness therefore require adequate documentation for the given configuration and the product used.

Airflow and negative pressure

The system uses airflow and negative pressure to help remove loose dust particles and reduce unpleasant odours.

This technology is not intended to remove dried or strongly adhering dirt.

Here, “dirt removal” means removing loose dust particles, rather than mechanical washing or stain removal. Airflow alone does not provide a documented guarantee that a wet helmet will dry completely. The drying function and its parameters must be confirmed for the specific model and configuration.

Deodorization and fragrance refreshment

Depending on the configuration, the machine may use a fragrance or freshening refill to make the equipment more pleasant to use again.

The availability of specific scents and their settings depends on the version of the device.

Air filtration

The machines also use honeycomb activated carbon to treat the air and reduce odours.

Filter material is part of regular operational maintenance.

Important note: The machine does not replace classic mechanical washing or the cleaning and maintenance procedures recommended by the helmet manufacturer. This is not a brush washer and the device is not designed to remove dried mud, grease, oil stains or deep soiling.

5. What helmets and other equipment can be treated?

The machines are primarily intended for compatible protective and sports helmets, for example:

Motorcycle helmets.
Karting and motorsport helmets.
Bicycle helmets.
Ski helmets.
Riding helmets.
Selected other sports and work safety helmets.

Can helmet and gloves be treated at the same time?

Yes. The manufacturer confirmed the possibility of joint treatment of helmet and gloves in one cycle.

The condition is adequate size, material compatibility and correct placement of equipment in the chamber.

Material compatibility and limitations

It is always necessary to take into account the instructions of the manufacturer of the specific helmet before use.

It is particularly important to verify compatibility with:

Helmet shell material.
Paint and surface treatments.
Internal padding and lining.
Adhesives and bonding materials.
Visors and other sensitive components.
Electronic accessories and communication systems.

Universal compatibility with all types of helmets and materials is not proven. The suitability of specific equipment must therefore be verified in advance.

6. Where can machines be used?

Self-service machines for cleaning and disinfecting helmets are used wherever regular maintenance of protective equipment is needed.

Kart tracks and motorsport centers

Hygienic treatment of shared rental helmets between sessions.

Motorcycle centers and motorcycle equipment stores

The ability to offer customers a new paid service or additional care for their own equipment.

Bike parks and bike rentals

Treatment of shared bicycle helmets and increased comfort for visitors.

Ski resorts and rental shops

Regular maintenance of rented ski helmets in seasonal operation.

Equestrian clubs and sports grounds

Possibility of hygienic treatment of compatible riding helmets.

Industrial and experience operations

Care of shared protective equipment after prior verification of material compatibility.

7. Technical parameters of SINGLE and DUO machines

Below we present the available technical data for a basic orientation in the selection of equipment and preparation of installation.

Technical parameter	Value / specification
Model Series	SINGLE / DUO
Product designation	EKH01 / EKH01DUO according to commercial variant
Number of chambers SINGLE	2; chambers can run independently or simultaneously
Number of chambers DUO	2, both independent triggering and concurrent operation
Dimensions SINGLE (W x D x H)	Approx 660 x 600 x 1966mm
DUO dimensions (W x D x H)	Approx 650 x 600 x 2025mm
Weight SINGLE	Not yet verified, must be confirmed for a specific variant
Duo weight without packaging	109 kg for the basic version
Duo weight in export packaging	186 kg
Export packaging dimensions	Must be requested for a specific delivery
SINGLE display	Touch, approximately 12.1″
DUO Display	Touch, approximately 15.6″
Customer Control	Self-service via touch screen
Electrical supply	Approximately 230 V, depending on the configuration
Maximum Power	2,100 W stated so far, figure not verified for all models
Frequency, Fusing and Electrical Requirements	According to the production plate and the final technical sheet
Water connection	There is no need
Sewage connection	There is no need
Network Communication	Wi-Fi / 4G, or Ethernet, depending on the design
Remote Administration	Manufacturer's web-based online platform
Standard environment	Interior, recommended ambient temperature above 0 °C
Ambient humidity range	Not yet confirmed
Low-temperature adaptation	Specially adapted components can be considered individually, with declared usability down to −18 °C.
IP protection rating	Not yet confirmed, need to verify for specific installation
Language versions	Multiple languages available upon order
Slovak and Hungarian	Available with an additional fee for translation

Dimensions, display sizes, electrical parameters and communication options represent the available data of the product line. Mandatory values are confirmed in the technical specification of a specific device.

8. Online monitoring and remote management

The available solution includes the manufacturer’s web platform for remote monitoring of machine operation.

Thanks to it, the operator can monitor selected operating data without the need to physically check the machine.

What information can be tracked?

Current Device Status

Overview of the operating status of the machine in real time.

Revenues and sales

Display revenue and sales data recorded by the device.

Individual transactions

Ability to track records of individual transactions. The completeness of the payment details depends on the specific integration of the payment system.

Number of completed cycles

Overview of the daily and total number of started cycles.

Error messages

Display error codes, operational warnings and selected device status information.

Service Notice

E-mail maintenance reminders according to set service intervals.

Monitoring disinfectant refill usage

An estimated number of treatment cycles can be set for the disinfectant refill.

Separate monitoring of the fragrance refill

The cycle allowance for the fragrance refill can be set independently of the disinfectant refill.

Remaining cycle counters may not represent a direct physical measurement of fluid level. This may be a calculation based on the set number of uses.

Remote parameter setting

The platform allows basic remote configuration of selected functions. The range of settings varies by software version.

Is there a fee for online monitoring?

The manufacturer's standard web platform is provided without a monthly or annual software fee.

However, the payment system is a separate service that may be subject to additional fees.

Additional online management options

The following features are not yet universally confirmed:

Export data to XLS or CSV.
Manage multiple machines under one user account.

Their availability must be verified according to the specific software solution.

9. Payment system and payment options

Machines can be equipped with a self-service cashless payment terminal NAYAX according to the ordered configuration.

Supported payment methods may include:

Visa payment cards.
Payment cards Mastercard.
Contactless payments via NFC.
Supported mobile wallets.

The specific options depend on the terminal used, the country of installation and the approval of the payment account.

Technical requirements of the payment terminal

When preparing the contract, the following is confirmed in particular:

The exact payment terminal model.
Supported payment methods.
A communication protocol such as MDB.
Necessary cabling and connection to the machine.
Mobile signal or data connection requirements.
Local conditions for processing payments.
Payment account activation.

Important: The online machine management platform and the payment processing platform are two separate systems.

The operation of the payment terminal may include activation, periodic and transaction fees according to the terms and conditions of the payment service provider.

10. Consumables, refills and operational maintenance

For the proper functioning of the device, it is necessary to use compatible disinfectant, cleaning and refreshing products and to follow service procedures.

Disinfecting and refreshing refills

The machine uses liquid products designed for fine spraying.

Clarification for the single-chamber SINGLE model: “Water or disinfectant” describes the liquid used in the spray system, rather than washing the helmet with water. The specific product and any dilution must follow the manufacturer’s instructions; water alone does not replace a disinfectant.

The product used must meet the requirements for:

Compatibility with spray system.
Appropriate chemical composition.
Material compatibility with treated equipment.
Safe use according to manufacturer's instructions.
Compliance with relevant EU regulations.

Package volume and approximate consumption

The manufacturer specifies a 5-litre product container, providing approximately 500 treatments.

Actual consumption depends on program length, dosage and device configuration.

Dilution of preparations

According to the available technical information, dilution with water is required for the mentioned product.

The purpose of proper dilution is, among other things, to reduce the formation of a slippery coating on the surface of the helmet.

The exact dilution ratio must be confirmed for the specific product, and the prescribed procedure must be followed.

The preparation of the filling may require water, but the machine itself does not need a direct connection to the water supply.

Can I use my own disinfectants?

Yes, after their suitability has been verified.

Refills can be purchased from the equipment supplier or compatible locally available preparations can be used.

Before using an alternative preparation, it is necessary to verify in particular:

Safety data sheet (SDS).
Chemical and material compatibility.
Suitability for the spray system used.
Dilution instructions.
Compliance with relevant European legislation.

Air filter and its replacement

The device uses Honeycomb Activated Carbon Filtration to help condition the air and reduce odors.

The manufacturer recommends replacement approximately every 3 months.

Actual interval may vary based on usage intensity and service instructions.

Refilling

The devices have filling points according to the specific design. The exact procedure for topping up and maintenance is given in the relevant service manual.

What are the operating costs?

Total operating costs depend mainly on:

Consumption of disinfectant and fragrance refills.
Replacement filter materials.
Electric energy.
How intensively the machine is used.
Fees for payment services.
Service and regular maintenance.

Operating costs cannot be determined only according to liquid consumption. It is possible to prepare an individual calculation for a specific operation.

11. Installation and Location Requirements

CENTRUMO machines do not require a water or sewage connection. However, for their operation, it is necessary to provide an adequate electrical power supply and, depending on the configuration, also an Internet connection.

Standard indoor location

The basic design is intended for indoor environments with a recommended ambient temperature above 0 °C.

Before installation, it is necessary to ensure:

Enough space to accommodate equipment.
Operating clearance for opening doors and accessing chambers.
Access to filling points and service areas.
Firm and level ground with adequate bearing capacity.
Electrical connection complying with the rating plate and local regulations.
Reliable network connection for online administration and possibly a payment terminal.
Sufficient mobile signal if the specific configuration requires it.

Can the machine be installed outdoors?

Outdoor installation can be assessed individually, but is not a guaranteed feature of the standard version.

For more demanding temperature conditions, specially adapted components with declared usability down to −18 °C can be considered.

This is not a standard feature of DUO. The −18 °C figure concerns specially adapted components, rather than confirmed weather resistance of the entire machine. Suitability of the complete machine for the intended conditions must be confirmed for its specific configuration.

However, low temperature resistance alone does not mean that the device simultaneously resists:

Rain and snow.
Increased humidity.
Condensation.
Sun and UV radiation.
Salt-laden air.
Vandalism.

The degree of IP protection and the exact permitted humidity range have not yet been confirmed. Both data must be verified for the specific configuration before installation.

For outdoor installation, the specific location and required weather protection must therefore be assessed in advance.

What to prepare before installation?

For a correct placement proposal, it is advisable to specify in advance:

Floor space and the required operating clearances.
Bearing capacity and flatness of the base.
Electrical requirements according to the final specification.
Availability of data or mobile connection.
Conditions for equipment protection during possible outdoor operation.
Required language interface.
Branding and possible individual modifications.
Service access and the scope of handover training.

12. Language versions, branding and individual settings

The machines can be adapted to the needs of the operator and their customers.

Depending on the version, options may include:

Custom graphics and decals

Possibility to adapt the appearance of the machine to the visual identity of the operator, including the logo and graphic elements.

Multilingual User Interface

The machine may support several languages and switching between them. The required languages are agreed when ordering.

According to the available information, Slovak and Hungarian are available for an additional translation fee.

Customer workflow configuration

The self-service interface and payment workflow can be configured as agreed.

Editing cleaning programs

Selected versions allow individual program settings if their technical and software equipment supports it.

Special Use

Modifications for a specific type of equipment can also be addressed after a technical assessment.

Availability of individual modifications, possible surcharges and technical options are confirmed individually.

13. Special configuration for helmets and footwear

Alongside the standard SINGLE and DUO models, a custom design with separate chambers for a helmet and footwear can be assessed individually.

This is not a confirmed standard production model. Such a design requires a separate technical specification, engineering assessment and approval.

What shoe materials may be suitable?

The manufacturer states the possibility of treating shoes from the following materials:

Textiles.
Mesh.
Smooth leather.
Gore-Tex.

Suede materials are not recommended.

How is footwear treated?

The process uses hygienic treatment technology without brush mechanical washing and without connection to water supply or sewage.

According to the manufacturer's information, the shoes should be dry and ready to use after the cycle is completed.

The actual result depends on the material, condition and specific design of the shoe.

This option requires individual development and technical confirmation. It is not an automatic part of commonly offered helmet treatment models.

14. Delivery, Warranty and Service Support

CENTRUMO provides customers with consultation on a suitable solution, configuration design, preparation of an individual offer and coordination of delivery, installation and subsequent support according to the agreed terms.

Delivery period

Standard delivery time is usually between 90-120 business days.

The exact term depends on the chosen configuration, the scope of modifications and the confirmation of the order.

Warranty conditions

According to the available commercial documents, the standard warranty period is 12 months.

An extension of the warranty to a total of 24 months can be agreed for an additional 10% of the machine price.

Specific warranty and service conditions are specified in the individual price offer and contract.

15. Technical documentation for the device

Before confirming the order, it is advisable to specify the scope of the documentation supplied for a specific configuration.

According to the type of equipment and contract, these are mainly:

The model’s binding technical data sheet.
Electrical requirements and installation conditions.
Dimensional drawing of the device.
Instructions for use and maintenance.
Conformity documents, including the EU declaration of conformity for the supplied configuration.
Safety data sheets (SDS) for the products used.
Instructions for the payment terminal if included in the delivery.

The range of documents actually supplied must be confirmed before the order and specified in the specific offer.

16. Frequently Asked Questions (FAQ)

Is the helmet cleaning and disinfection machine fully self-service?

Yes. The customer controls the process through the touchscreen, selects an available programme and, where applicable, makes a cashless payment.

How long does it take to clean a helmet?

Available programs have an approximate length of 3 minutes (Quick), 5-7 minutes (Medium) and 10 minutes (Deep). The exact length depends on the settings of the specific machine.

Can a machine clean a heavily soiled helmet?

The machine is not a mechanical washer. It is intended for hygienic treatment, freshening and removal of loose dirt, rather than dried mud, oil, grease or deep stains.

Can helmet and gloves be treated in one cycle?

Yes if their co-location in the chamber is possible and they meet the size and material compatibility requirements.

Can both chambers work simultaneously with the DUO model?

Yes. Both chambers operate independently. Only one or both can be run at the same time.

Does the machine need a water or waste connection?

No. The machine does not require a direct water or drainage connection. Water may, however, be needed to prepare and dilute the disinfectant refill as prescribed.

Can I use my own disinfectants?

The use of locally available preparations is possible after verification of their compatibility, safety data sheet and compliance with relevant regulations. You cannot automatically use any cleaning or disinfecting agent.

How often do you need refills?

The frequency of refilling depends on the selected programs, dosage and number of cycles. The manufacturer gives an approximate estimate of 500 treatments per 5 liters of product.

How often is the air filter changed?

The manufacturer recommends replacing the honeycomb activated carbon approximately every 3 months. The interval may vary depending on the load on the device.

Is online monitoring free?

The manufacturer's standard web platform does not have a monthly or annual software fee. Payment terminal and transaction processing fees, if any, are separate.

Can sales and number of uses be tracked?

Yes. The platform allows you to track operational status, sales, individual transactions, daily and total number of cycles, and selected service alerts. The range of details depends on the configuration.

Can multiple machines be managed from one account?

This option is not universally confirmed yet and must be verified for a specific software version.

Can operational data be exported to Excel or CSV?

XLS/CSV export is not yet confirmed. Its availability needs to be verified with a specific configuration.

Is it possible to use the machine outdoors?

Outdoor installation is assessed individually. A low-temperature adaptation may be considered for selected conditions, but protection against water, humidity, snow and other environmental factors must be verified separately.

Can I put my own logo on the machine?

Yes. Branding, graphic wraps and other visual changes can be agreed individually.

Does the machine support multiple languages?

Yes, depending on the configuration. The required languages and any additional charges are agreed when ordering. Slovak and Hungarian are available for an additional translation fee.

What documents are supplied with the device?

The range of technical documentation, manuals, safety data sheets and conformity documents including the EU declaration of conformity must be confirmed for a specific configuration before ordering.

Can the machine be adapted for cleaning shoes?

A special design with separate chambers for a helmet and footwear can be assessed individually. This is not a confirmed standard production model and requires a separate specification and approval.

17. How to choose a suitable machine?

When choosing the right model, it is important to take into account type of operation, number of customers, frequency of use of helmets, required capacity and installation location.

SINGLE with one chamber can be a suitable solution for smaller and moderately busy operations. For places with a higher frequency of visitors and a larger amount of shared equipment, it is advisable to consider DUO with two independent chambers.

Do you need advice on choosing?

To recommend a suitable design, please tell us:

Type of operation in which you want to use the machine.
Expected number of customers or helmets in use.
Planned location, i. e. interior or exterior space.
Required payment method.
Country of installation.
Estimated date of delivery or commissioning.
Any requirements for branding, language versions or individual adaptations.

Based on this information, we will help you select a suitable model, propose a configuration and prepare an individual quotation.

CENTRUMO – self-service solutions for modern operations.

All listed technical parameters and functions may vary depending on the specific model, production version and ordered equipment. The information is indicative in nature. Binding parameters, scope of documentation and business conditions are always confirmed in an individual offer.

More information: www.centrumo.cz